Alignment Pump and Motor Training Program – Motor-Pump alignment is the process of aligning shaft centerlines between a motor and a pump. The motor is the prime mover, transferring power to the pump by the use of a coupling. This is probably the most common configuration of coupled machines in industry. In this type of alignment, the motor is almost always the moveable machine, and the pump is the stationary machine. In almost all cases, the pump is already piped up with suction and discharge flanges, which means it can move only slightly, if at all.
Proper shaft alignment is achieved by moving the motor. The motor is shimmed vertically to achieve the proper elevation to align it to the pump, both parallel (offset) and angular. The motor is them moved horizontally to achieve proper horizontal placement for aligning the shaft centerlines, both parallel and angular. Also, the motor is moved horizontally by the use of jacking bolts, or by the use of pry bars, hammers, or other tools.
Motors are normally easier to move, since the motor is not piped into a process system. A short run of flexible conduit is most often used to run the electrical wiring from a local disconnect, or a rigid conduit, to the motor termination box. This allows for ease of movement of the motor.
——————————————————————————-
INFORMASI DAN PENDAFTARAN
HUBUNGI: FERDI
0812 2681 1987
(PHONE/SMS/WHATSAPP)
——————————————————————————
Alignment Pump and Motor Training Content
1. Fundamental Alignment
2. Diagnosing Misalignment
3. Measuring Misalignment
4. Preparing Task Alignment
5. Alignment Methods
- Rough Methods
- Face and Rim
6. Alignment Tolerances
7. Complicating Factor Alignment.
8. Introduction to Laser Alignment
9. Minimizes the forces of misalignment acting upon the bearings and seals of both components.
10. Minimizes Wear of The Coupling.
11. Reduce Energy Costs.
12. Maximizes the life of the Machine Components by Minimizing Wear, increasing time between failures, and reducing vibration.
Participants
Instrument Engineer/Supervisor, Plant Maintenance/Operators/Supervisors
Alignment Pump and Motor Training Method
- Presentation
- Discussion
- Simulation
- Case Study
- Evaluation
Waktu dan Tempat
Tanggal:
- Untuk Mendapatkan Jadwal Terbaru Silahkan Hubungi Kami
- TRAINING ONLINE sangat kami rekomendasikan dalam kondisi dan situasi yang menuntut Protokol COVID-19
- Training ini bisa kami laksanakan secara tatap muka di kota-kota besar sesuai dengan request anda sebagai peserta
- Kami juga memfasilitasi Inhouse Training yang efektif dan efisien untuk perusahaan anda.
Lokasi: The 1O1 Hotel Yogyakarta/Neo Malioboro Hotel Yogyakarta/Ibis Styles Hotel Yogyakarta
Biaya Training Offline
- Rp 6.500.000,-/peserta (non residensial)
- Rp 5.500.000,-/peserta (non residensial)/minimal 3 Peserta dari perusahaan yang sama
- Harga Rp 3.500.000,-/peserta (non residensial)/minimal 5 Peserta dari perusahaan yang sama
- Biaya Training Online akan menyesuaikan
- Inhouse Training bisa kami laksanakan sesuai dengan permintaan perusahaan. Hubungi kami untuk mendapatkan penawaran terbaik.
Fasilitas
- Modul Training
- Flash disk Materi Pelatihan
- Sertifikat Pelatihan
- Training Kit
- Souvenir
- Tas/Backpack
- Photo Pelatihan
- Makan Siang dan 2 x Coffee break
- Ruang Training Berkualitas
——————————————————————————-
INFORMASI DAN PENDAFTARAN
HUBUNGI: FERDI
0812 2681 1987
(PHONE/SMS/WHATSAPP)
——————————————————————————
image source: https://benchmarkpdm.com/getting-the-right-angle-in-shaft-alignment/